Tektronix Encore

Amplifier Research 200S1G4
Microwave Amplifier 0.8 - 4.2 GHz, 200W

Amplifiers - RF and Microwave >> Above 1 GHz and 101 Watt to 999 Watt >> Microwave Amplifier 0.8 - 4.2 GHz, 200W
Rent Used Test Equipment
Manufacturer: Amplifier Research
Model: 200S1G4

Amplifier Research 200S1G4 Microwave Amplifier 0.8 - 4.2 GHz, 200W

Electronic Test and Measurement Equipment

Amplifier Research 200S1G4 Microwave Amplifier 0.8 - 4.2 GHz, 200W Product Datasheet Download Product Datasheet

Rent Test Equipment

Product Overview


The Amplifier Research 200S1G4 Microwave Amplifier is portable, self-contained, air-cooled, broadband, and completely solid-state. The 200S1G4 Amplifier was designed for applications where instantaneous bandwidth, high gain and linearity are required. Push-pull circuitry is utilized in all high power stages in the interest of lowering distortion and improving stability. The Model 200S1G4, when used with a sweep generator, will provide a minimum of 200 watts of RF power.

The AR 200S1G4 is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a digital display, menu assigned softkeys, a single rotary knob, and four dedicated switches (POWER, STANDBY, OPERATE and FAULT/RESET) to offer extensive control and status reporting capability. The display provides operational presentation of Forward Power and Reflected Power plus control status and reports of internal amplifier status. Special features include a gain control, internal/external automatic level control (ALC) with front panel control of the ALC threshold, pulse input capability and RF output level protection. Also included is an internal RF detector which provides an output for use in self-testing or operational modes.

All amplifier control functions and status indications are available remotely in GPIB / IEEE-488 format and RS-232 hardwire and fiber optic. The buss interface connector is located on the back panel and positive control of local or remote operation is assured by a keylock on the front panel of the amplifier.

The low level of spurious signals and linearity of the Model 200S1G4 make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.

Specifications of the Amplifier Research 200S1G4 include:

  • RATED OUTPUT POWER: 200 watts minimum
  • INPUT FOR RATED OUTPUT: 10 milliwatt maximum
    • Nominal 230 watts
    • Minimum 180 watts
    • Nominal 210 watts
    • Minimum 160 watts
    • 25 dB maximum
    • ±10 dB with internal leveling
  • FREQUENCY RESPONSE: 08-42GHz instantaneously
  • GAIN (at maximum setting): 53 dB minimum
  • GAIN ADJUSTMENT: 15 dB minimum
  • INPUT IMPEDANCE: 50 ohms, VSWR 20:1 maximum
  • OUTPUT IMPEDANCE: 50 ohms, VSWR 25:1 maximum
  • MISMATCH TOLERANCE *: 100% of rated power without foldback Will operate without damage or oscillation with any magnitude and phase of source and load impedance
  • MODULATION CAPABILITY: Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal
  • HARMONIC DISTORTION: Minus 20 dBc maximum at 200 watts
  • RF POWER DISPLAY: Digital, forward and reflected
  • PRIMARY POWER: 120-240VAC 50/60 Hz, single phase 2150 watts
    • RF Connectors See Model Configurations
    • Detected RF output Front Panel
    • Safety interlock  15 pin female subminiature D on rear panel
    • Remote computer interfaceIEEE-488 (GPIB)& RS-232 connector on rear panel
    • Remote Computer Interface (Fiber Optic) ST Conn Tx and Rx RS-232
    • OthersFront Panel
  • IEEE-488 (GPIB) INTERFACE & RS-232: Allows control and monitoring of all front panel controls except keylock position control
  • COOLINGForced air (self contained fans)


Request A Quote

Rent      Buy      Repair


Home   |   Rental Equipment   |   Equipment Sales   |   Repair & Calibration   |   Sell Your Equipment   |   About Us   |   Contact   |   Get A Quote   |   Blog    

YouTube Facebook Google Plus Paypal
Get the latest deals first. Subscribe to our newsletter.    SUBSCRIBE

© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML     
© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML

Axiom Test Equipment
2610 Commerce Way Vista, CA 92081
Phone: (760) 806-6600