Amplifier Research 40S1G4
Microwave Amplifier, 0.7 - 4.2 GHz, 40 W
Amplifiers - RF and Microwave >> Above 1 GHz and 100W or Less >> Microwave Amplifier, 0.7 - 4.2 GHz, 40 W
Model: 40S1G4
|
Download Product Datasheet
Product Overview
RENT AMPLIFIER RESEARCH 40S1G4 (Call for Availability)
The Amplifier Research 40S1G4 is a solid state, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth, high gain, and linearity are necessary. It is housed in a stylish cabinet, designed for benchtop use, but can also be removed for immediate equipment rack mounting.
Features and Specifications of the Amplifier Research 40S1G4 include:
- Features:
- Provides a minimum of 40 watts of RF power when used with a sweep generator
- Front panel gain allows convenience of setting desired output level
- RF input leveling circuit:
- Controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm
- Protects the amplifier from RF input overdrive
- RF amplifier stages are protected from over-temperature by removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure
- Digital display on the front panel indicates the operate status and fault conditions when an over-temperature or power supply fault has occurred
- All control functions and status indications are available remotely in GPIB/IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet
- Bus interface connector is located on the back panel
- Local/Remote switch on front panel assures positive control of local or remote operation
- Low level of spurious signals and linearity make it ideal for these various uses:
- As a driver amplifier in testing wireless and communication components and subsystems
- As a test instrument covering multiple frequency bands
- For communication technologies including CDMA, W-CDMA, TDMA, GSM, etc.
- For EMC Test applications where undistorted modulation envelopes are needed
- Specifications:
- Rated power output: 40 watts minimum
- Input for rated output: 1.0 milliwatt maximum
- Power Output@ 3dB compression:
- Nominal: 50 watts
- Minimum: 40 watts
- Power Output@ 1dB compression:
- Nominal: 44 watts
- Minimum: 35 watts
- Flatness:
- Typical: ±1.5 dB
- Maximum: ±2.0 dB
- Frequency response: 0.7 – 4.2GHz instantaneously
- Gain (at maximum setting): 46 dB minimum
- Gain adjustment (continuous range): 10 dB minimum (4096 steps remote)
- Input impedance: 50 ohms, VSWR 2.0:1 maximum
- Output impedance: 50 ohms, nominal
- Mismatch tolerance:
- 100% of rated power without foldback
- Will operate without damage or oscillation with any magnitude and phase of source and load impedance
- Modulation capability: Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal
- Third order intercept point: 55 dBm typical
- Noise figure: 10 dB typical
- Harmonic distortion: Minus 20 dBc maximum at 40 watts
- Spurious: Minus 73 dBc typical
- Phase Linearity: ±1.0 deg/100 MHz, typical
- Primary power (selected automatically):
- 90-132, 180-264 VAC
- 50/60 Hz, single phase
- 285 watts maximum
- Connectors:
- RF: Type N female
- Remote interfaces:
- IEEE-488: 24 pin female
- RS-232: 9 pin Subminiature D (female)
- RS-232 (fiber optic): Type ST
- USB 2.0: Type B
- Ethernet: RJ-45
- Safety interlock: 15 Pin Subminiature D
- Cooling: Forced air (self contained fans)
REQUEST A QUOTE
| Testimonials |
|
I just wanted to say thank you. You guys are constantly dealing with our outrageous (and sometimes off the wall) demands and requests with the upmost care and professionalism. You guys are quick and give a level of quality that you dont often see, it is refreshing and a wonderful feeling to know that you guys have our backs. -- Tony B. Carlsbad, CA |
