Tektronix Encore

Amplifier Research 30S1G6
Microwave Amplifier, 1 - 6 GHz, 30W

Amplifiers - RF and Microwave >> Above 1 GHz and 100W or Less >> Microwave Amplifier, 1 - 6 GHz, 30W
Rent Used Test Equipment
Manufacturer: Amplifier Research
Model: 30S1G6

Amplifier Research 30S1G6 Microwave Amplifier, 1 - 6 GHz, 30W

Electronic Test and Measurement Equipment

Amplifier Research 30S1G6 Microwave Amplifier, 1 - 6 GHz, 30W Product Datasheet Download Product Datasheet

Rent Test Equipment

Product Overview

Rent Amplifier Research 30S1G6 Microwave Amplifier (Call for Availability): 


The Amplifier Research Model 30S1G6 is a solid-state, Class A design, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth and high gain are required. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet for immediate equipment rack mounting. The 30S1G6, when used with a sweep generator, will provide a minimum of 30 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The AR 30S1G6 is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from over-temperature by removing the DC voltage to them if an over temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions when an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared. The Amplifier Research 30S1G6 includes digital control for both local and remote control of the amplifier. All amplifier control functions and status indications are available remotely in GPIB/IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet. The bus interface connector is located on the back panel and positive control of local or remote operation is assured by a Local/Remote switch on the front panel of the amplifier. The export classification for this equipment is EAR99.


Functions and Specifications of the Amplifier Research 30S1G6 Microwave Amplifier Includes:


RATED POWER OUTPUT: 30 watts minimum (1.0-6GHz)



Nominal: 40 watts

Minimum: 28 watts



Nominal: 30 watts

Minimum: 22 watts


SMALL SIGNAL GAIN FLATNESS: ±1.5 dB typical ±2.0 dB maximum


FREQUENCY RESPONSE: 1.0–6GHz instantaneously


INPUT FOR RATED OUTPUT: 1.0 milliwatt maximum


GAIN (at maximum setting): 44 dB minimum


GAIN ADJUSTMENT (Continuous Range): 10 dB minimum

(4096 steps remote)


INPUT IMPEDANCE: 50 ohms, VSWR 2.0:1 maximum


OUTPUT IMPEDANCE: 50 ohms, nominal


MISMATCH TOLERANCE: 100% of rated power without foldback. Will

operate oscillation with any magnitude and phase of source

and load impedance.


MODULATION CAPABILITY: Will faithfully reproduce AM, FM, or pulse

modulation appearing on the input signal


HARMONIC DISTORTION: Minus 20 dBc maximum at 25 watts


SPURIOUS : Minus 73 dBc typical




NOISE FIGURE: 10 dB typical


PRIMARY POWER (selected automatically): 90-132, 180-264 V

AC 50/60 Hz, single phase 300 watts maximum


SAFETY INTERLOCK: 15 Pin Subminiature D


COOLING: Forced air (self contained fans)



Request A Quote

Rent      Buy      Repair


Home   |   Rental Equipment   |   Equipment Sales   |   Repair & Calibration   |   Sell Your Equipment   |   About Us   |   Contact   |   Get A Quote   |   Blog    

YouTube Facebook Google Plus Paypal
Get the latest deals first. Subscribe to our newsletter.    SUBSCRIBE

© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML     
© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML

Axiom Test Equipment
2610 Commerce Way Vista, CA 92081
Phone: (760) 806-6600