Rent Amplifier Research 100S1G6AB Microwave Amplifier (Call for Availability):
The Amplifier Research 100S1G6AB is a solid-state, Class AB design, self-contained, aircooled, broadband amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet for immediate equipment rack mounting.
The 100S1G6AB, when used with a sweep generator, will provide a minimum of 100 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The 100S1G6AB is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from overtemperature by removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions if an overtemperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared. All amplifier control functions and status indications are available remotely in GPIB/IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet. The bus interface connector is located on the back panel and positive control of local or remote operation is assured by a Local/Remote switch on the front panel of the amplifier.
The low level of spurious signals and linearity of the Amplifier Research 100S1G6AB make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.
Functions and Specifications for the Amplifier Research 100S1G6AB Microwave Amplifier Includes:
RATED POWER OUTPUT: 100 watts minimum (1.0–6 GHz)
INPUT FOR RATED OUTPUT: 1.0 milliwatt maximum
POWER OUTPUT @ 3dB COMPRESSSION
Nominal: 100 watts
Minimum: 80 watts
POWER OUTPUT @ 1dB COMPRESSION
Nominal: 50 watts
Minimum: 30 watts
SMALL SIGNAL GAIN FLATNESS: ±1.5 dB typical ±2.5 dB maximum
FREQUENCY RESPONSE: 1.0–6 GHz instantaneously
GAIN (at maximum setting): 50 dB minimum
GAIN ADJUSTMENT (Continuous Range; 4096 steps remote):
10 dB minimum
INPUT IMPEDANCE: 50 ohms, VSWR 2.0:1 maximum
OUTPUT IMPEDANCE: 50 ohms, nominal
MISMATCH TOLERANCE (@ Rated POUT): 3:1 at all load phase.
MODULATION CAPABILITY: Will faithfully reproduce AM, FM, or pulse
Modulation appearing on the input signal
THIRD ORDER INTERCEPT: 56 dBm typical
NOISE FIGURE: 10 dB typical
HARMONIC DISTORTION: Minus 20 dBc typical at 80 watts
SPURIOUS: Minus 73 dBc Typ.
PHASE LINEARITY: 1.0 deg/100 MHz, Typ
PRIMARY POWER (Selected Automatically): 90-132, 180-264 VAC;
50/60 Hz, single phase 525 watts maximum
SAFETY INTERLOCK: 15 pin Subminiature D
COOLING: Forced air (self contained fans)
EXPORT CLASSIFICATION: 3A001
Request A Quote
Customers who viewed this also viewed
Amplifier Research 100A250A RF Amplifier, 10 kHz - 250 MHz, 100W
Amplifier Research 50S1G4A Microwave Amplifier, 0.8 - 4.2 GHz, 50W
Amplifier Research 75A250A RF Amplifier, 10 kHz - 250 MHz, 75W
COM-POWER PAM-118A PreAmplifier, 500 MHz - 18 GHz, 40db