California Instruments MX45-3PI Power System, 45kVA, 1 and 3-Phase, Programmable Rental, Repair, Rent, Used


Tektronix Encore




California Instruments MX45-3PI
Power System, 45kVA, 1 and 3-Phase, Programmable

Power Supplies >> AC Power Sources, More than 10kVA >> Power System, 45kVA, 1 and 3-Phase, Programmable
Rent Used Test Equipment
Manufacturer: California Instruments
Model: MX45-3PI

California Instruments MX45-3PI Power System, 45kVA, 1 and 3-Phase, Programmable

Electronic Test and Measurement Equipment

California Instruments MX45-3PI Power System, 45kVA, 1 and 3-Phase, Programmable Product Datasheet Download Product Datasheet

Rent Test Equipment

Available Option Configurations

Config-02

  • 208 - 208VAC input, L-L, 3 wire + Ground
  • HF - Increases maximum frequency to 1000Hz
  • SNK - Regenerative Source
  • MSRP: $78,429 | Available for Rental    GET QUOTE  

Config-03

  • 208 - 208VAC input, L-L, 3 wire + Ground
  • HF - Increases maximum frequency to 1000Hz
  • HV - Adds 400 V AC-only Output Range
  • SNK - Regenerative Source
  • MB - Allows two MX45's to become one MX90 (DB37 cable required)
  • MSRP: $84,290 | Available for Rental    GET QUOTE  

Product Overview

CALIFORNIA INSTRUMENTS MX45

The California Instruments MX45-3Pi Test System consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications. This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the California Instruments MX45-3Pi Test System combines compactness, robustness and functionality in a compact floor-standing chassis. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the unit to its designated location (using included casters), plug it in, and the California Instruments MX45-3Pi Test System is ready to work for you.

The California Instruments MX45-3Pi Test System can be operated completely from its menu driven front panel controller. A backlit LCD display shows menus, setup data, and read-back measurements. IEEE-488, RS232C, USB and LAN remote control interfaces and instrument drivers for popular ATE programming environments are available. This allows the California Instruments MX45-3Pi to be easily integrated into an automated test system. For advanced test applications, the California Instruments MX45-3Pi Test System, with its programmable controller, offers full arbitrary waveform generation, time and frequency domain measurements, and voltage and current waveform capture.

The California Instruments MX45-3Pi Test System delivers up to 45 kVA of single phase output. It allows switching between single and three phase output modes. In DC mode, 65% of the AC power level is available and AC + DC mode is also supported. The built-in output transient generation and read-back measurement capability of the MX45-3Pi offers the convenience of a powerful, and easy to use, integrated test system.

Features and Specifications of the California Instruments MX45-3Pi Test System include:

  • Combines AC/DC source and power analyzer functions
  • AC, DC and AC+DC Operationg Modes
  • Powerful output transient generation
  • Arbitrary waveform generation
  • User defined voltage waveform and distortion programming
  • Harmonic analysis of Voltage and Current
  • Can deliver up to 300 Amps
  • Maximum current of 125 A rms
  • Multiple Chassis Configurations
  • Operating Modes: AC, DC and AC + DC
  • AC Mode Output:
    • Phase Outputs: 1 or 3 switchable, Neutral: Floating, Coupling: DC (except for -HV option)
    • Total Power:  45 kVA
    • Load Power Factor:  0 to unity at full output current
  • AC Mode Voltage:
    • Voltage Ranges:
      • AC:
        • V Low: 0-150V
        • V High: 0-300V
      • AC+DC:
        • V Low: 0-150V
        • V High: 0-300V
    • Load Regulation:  < 0.25 % FS DC to 100 Hz, < 0.5 % FS 100 Hz to 819 Hz
    • Line Regulation:  < 0.1% FS for 10 % line change
    • External Sense: Voltage drop compensation (5% Full Scale)
    • Harmonic Distortion (Linear): Less than 1% from 16 - 66 Hz, Less than 2% above 66 Hz, Less than 3% above 500 Hz
    • DC Offset: < 20 mV
    • External Amplitude Modulation:
      • Depth: 0 - 10 %
      • Frequency: DC - 2 KHz
    • Voltage Slew Rate: 200 μs for 10% to 90% of full scale change into resistive load
  • AC Mode Current:
    • Steady State AC Current @ FS V:
      • V Low: 100/ø / 300
      • V High: 50/ø / 150
    • Peak Repetitive AC Current: Up to 3.6 x rms current at full scale voltage
    • Programming Accuracy:
      • Voltage (rms): ± 0.3 Vrms
      • Frequency: ± 0.01 % of programmed value
      • Current Limit: - 0 % to + 5 % of programmed value + 1A
      • Phase: < 0.5° + 0.2°/ 100 Hz with balanced load
    • Programming Resolution:
      • Voltage (rms): 100 mV
      • Frequency: 0.01 Hz from 16 - 81.91 Hz, 0.1 Hz from 82.0 - 819 Hz
      • Current Limit:
        • 0.1 A, 3 phase mode
        • 1.0 A, 1 phase mode
        • Phase: 0.1°
  • DC Mode Output:
    • Power:
      • Maximum DC power at full scale of DC voltage range.
      • MX30-3Pi / 1Pi: 10 kW per output, 3 outputs. 30 kW in 1 channel mode
    • Voltage Ranges:
      • Low: 0 - 200V
      • High: 0 - 400V
    • Output Accuracy: ± 1 Vdc
    • Load Regulation: < 0.25 % FS
    • Line Regulation: < 0.1% FS or 10 % line change
    • Ripple: < 2 Vrms Lo Range, < 3 Vrms Hi Range
    • Max DC Current @ FSV per output:
      • V Low: 50 / 150
      • V High: 25 / 75
    • Current Limit: Programmable from 0 A to max current for selected range
  • AC+DC Mode Output:
    • Output (Pi) Power: Maximum current and power in AC+DC mode is same as DC mode
  • Protection:
    • Over Load: Constant Current or Constant Voltage mode
    • Over Temperature: Automatic shutdown
  • Storage / Non Volatile Memory Storage:  16 Instrument setups, 200 user defined waveforms
  • Waveforms:
    • Waveform Types:  Sine, Square, Clipped sine, user defined
    • User defined waveform storage: Four groups of 50 user defined arbitrary waveforms of 1024 points for a total of 200. One group can be active at a time
  • System Interface:
    • Inputs: Remote shutdown, External Sync, Clock/Lock (option on Pi)
    • Outputs: Function Strobe / Trigger out, Clock/Lock (option on Pi)


Request A Quote

Rent      Buy      Repair
SUBMIT REQUEST
760-806-6600







Home   |   Rental Equipment   |   Equipment Sales   |   Repair   |   Sell Your Equipment   |   About Us   |   Contact   |   Get A Quote   |   Blog    


Facebook Google Plus Paypal
Get the latest deals first. Subscribe to our newsletter.    SUBSCRIBE


© 2017 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML     
© 2017 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML

Axiom Test Equipment
2610 Commerce Way Vista, CA 92081
Phone: (760) 806-6600