Rent Amplifier Research 800A3 (Call for availability):
The Amplifier Research 800A3 is a self-contained, air-cooled, broadband, solid-state amplifier designed for applications where instantaneous bandwidth and high gain are required. The Amplifier Research 800A3, when used with an RF sweep generator, will provide a minimum of 800 watts of swept power.
The Amplifier Research 800A3 is equipped with a digital control panel which provides both local and remote control of the amplifier. The display provides operational presentation of forward power and reflected power, plus control status and reports of internal amplifier status. Special features include a gain control, RF output level protection, and a transformer with selectable taps for matching to different load impedances.
The 800A3 amplifier features an internal impedance transformer with selectable output impedance values of 12.5, 25, 50, 100, 200 and 400 ohms.
The thought process behind the 800A3 is because most RF amplifiers have a nominal internal impedance of 50 ohms, which is fine for most RF applications. But since more and more low to mid-frequency RF applications are now characterized by impedances other than the usual 50 ohms, AR RF/Microwave Instrumentation has created a family of RF power amplifiers that can incorporate a variable output impedance.
The unique impedance-matching capabilities along with the excellent mismatch tolerance makes the A3 series amplifiers extremely well suited to the ever-changing requirements of research & development applications as well as general purpose lab use.
The 800A3 amplifier was designed to be used in applications for fluorescent lighting, ultrasound, plasma generation and testing, mass spectrometers, piezoelectric crystals, EMC, and a variety of low to mid-frequency RF applications.
All amplifier control functions and status indications are available remotely in GPIB/IEEE-488, RS-232 and USB. The buss interface connectors are located on the back panel and positive control of local or remote operation is assured by a keylock on the front panel of the amplifier.
The 800A3 amplifier is intended for applications where the load impedance is not necessarily 50 ohms. The selectable output impedance provides the capability to drive loads that would otherwise cause a high SWR and limit the delivered power. The impedance matching transformer uses high-voltage/high-current vacuum relays so the user can “hot switch” between impedances without damage.
The Amplifier Research 800A3 is housed in a cabinet and designed to provide complete standalone performance for RF testing. It is also configured to be used as a sub-amplifier in a 1500 watt or 5000 watt higher power amplifier. It can be added in an incremental fashion to become a part of these higher power units yet still be used as a standalone 800 watt amplifier.
Functions and Specifications of Amplifier Research 800A3 (Call for availibility):
RATED POWER OUTPUT: 800 watts minimum
INPUT FOR RATED OUTPUT: 1.0 milliwatt maximum
POWER OUTPUT @ 3 dB compression
Nominal: 800 watts
Minimum: 700 watts
POWER OUTPUT @ 1 dB compression
Nominal: 500 watts:
Minium: 400 watts
FLATNESS: +1.0 dB maximum
FREQUENCY RESPONSE: 10 kHz–3 MHz instantaneously
GAIN (at maximum setting): 60 dB minimum
GAIN ADJUSTMENT (continuous range):23 dB minimum
INPUT IMPEDANCE: 50 ohms nominal
OUTPUT IMPEDANCE (switch select; manual): 12.5, 25, 50, 100, 150, 200, 400 ohms nominal (10kHz-3MHz) on front panel
MISMATCH TOLERANCE: 100% rated power without foldback up to 6.0:1 mismatch above which may limit to 400 watts reflected power. Will operate without damage or oscillation with any magnitude and phase of source and load impedance.
HARMONIC DISTORTION: Minus 20 dBc maximum at 400 watts power output.
MODULATION CAPABILITY: Will faithfully reproduce AM (within the linear power spec), FM, or pulse modulation appearing on the input signal.
OUTPUT CONNECTOR: See Amplifier Research configurations
INPUT CONNECTOR: See Amplifier Research configurations
REMOTE CONTROL: GPIB-IEEE-488/RS-232/USB, ability to remote control and power an external impedance transformer.
RF POWER DISPLAY: 0–1000 Watts full scale. Directional power monitor allows separate display of forward and reflected power.
POWER MONITOR.: BNC: 0-10V forward and reverse power
COOLING: Forced-air (self-contained fans)
PRIMARY POWER: Universal, 85–137/180–264VAC, 47–63 Hz, 2500 watts maximum.
Weight: 70 lbs
Dimensions (inches): 19.8x13.4x21.7
Other similiar RF Amplifiers include:
Testimonials |
We received our purchase from Axiom and everything was expertly packed and the items are 100% complete and operational. We’re definitely a satisfied customer. -- John G. Wernersville, PA |