Sorensen SGA800-18.7
DC Power Supply, 800V, 18.7A, 14960W

Download Product Datasheet

Product Overview

RENT SORENSEN SGA800-18.7 DC Power Supply, 800V, 18.7A, 1496W (call for availability)

The Sorensen SGA800-18.7 DC Power Supply is a high powered, programmable power supply designed for exceptional load transient response, low noise, and the highest power density in the industry. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units.

The Sorensen  SGA800-18.7 DC Power Supply (SGA = Sorensen General Purpose Analog), with its high performance power electronics, meets the need for simple front panel analog controls or external control. It provides essential features like 10-turn potentiometers for setting voltage and current, 3 ½ digit LED readout, plus front panel over-voltage protection (OVP) preview/adjustment and reset.

Features and Specifications of the Sorensen SGA800-18.7 DC Power Supply include:

• High Power Density: Up to 15 kW in a 3U chassis
• Wide Voltage Range: 0-10V up to 0-800V, in increments of 5 kW from 5 to 30 kW
• Fast Load Transient Response: Protection from undesired voltage excursions
• Low RMS and P-P Noise:  Suitable for the most sensitive applications
• Parallelable up to 150 kW: Expandable as your requirement grows
• Modular Design: Upgradeable for the ultimate in investment protection
• 16-bit Resolution:  Optional IEEE-488.2 + RS-232C + Ethernet provides precise control

Common:

• Remote Sense:  Terminals are provided to sense output voltage at point of load. Maximum line drop 5% of rated voltage per line for 40-100V models, line drop 1V of rated voltage per line for 10-20V models, 1.5V for 30V models, 2% of rated voltage per line for models 160V and greater. (Greater line drop is allowed, but output regulation specifications no longer apply).
• Parallel Operation:  Up to 5 units may be paralleled for additional current within the power supply single-unit specifications, with exception of the DC output current set accuracy. Additional paralleled SG units will add 0.3% inaccuracy per unit. To parallel more than 5 units, contact factory.
• Series Operation:  Up to 2 units

Input:

• Nominal Voltage 3 phase, 3 wire + ground: 
• 208/220 VAC (operating range 187 - 242 VAC)
• 380/400 VAC (operating range 342 - 440 VAC)
• 440/480 VAC (operating range 396 - 528 VAC)
• Frequency:  47 – 63Hz , 400Hz
• Power Factor: 
• >0.9 typical for 208/220 VAC input (10V - 800V)
• >0.78 typical for 380/400 VAC input (40V - 800V)
• >0.9 typical for 380/480 VAC input (10V - 30V)
• >0.7 typical for 440/480 VAC input (40V - 800V)
• >0.9 typical for 440/480 VAC input (10V - 30V)
• Protection:  ½ cycle ride-though on all three phases, 3 cycle ride through on single phase; missing phase shutdown (800V model 6.4 msec on all 3 phases)

Output:

• Voltage and Current Range: 800V, 18.7A, 15kW
• Ripple & Noise:
• rms(20Hz-300kHz): 80mV
• p-p: 500mV

Programming & Read-Back Specifications:

• Front Panel Display:
• Programming:
• Accuracy: +/- (0.5%fs + 1 digit)
• Resolution: 3.5 digits
• Read-Back Monitoring:
• Accuracy: +/- (0.5%fs + 1 digit)
• Resolution: 3.5 digits
• Knob control & Display read-back
• Remote Analog Interface: 
• Programming:
• Accuracy:
• Voltage: +/-0.25% of full scale
• Current: 0.8% of full scale 
• Read-Back Monitoring:
• Accuracy: +/-1.0% of full scale
• 25-pin D-sub connector (0~5 V or 0~10 V)
• Remote Digital Interface:
• Programming:
• Accuracy:
• Voltage:  +/- 0.1% of full scale
• Current: +/- 0.4% of full scale
• Resolution: +/-0.002% of full scale
• Read-Back Monitoring:
• Accuracy:
• Voltage:  +/- 0.15% of full scale
• Current:  +/- 0.4% of full scale
• Resolution:  +/-0.002% of full scale
• RS-232C (Standard on SGI), Optional IEEE-488.2 and Optional LXI Compliant 10/100 base-T Ethernet
• OVP:
• Programming:
• Accuracy: +/- 1% of full scale
• Resolution: +/-0.002% of full scale
• Programming range: 5-110% Configured from front panel, remote analog or via optional digital inputs
• User I/O:
• Disconnect & Polarity-reversal relay control (Only available with Ethernet Option)

Click to see all the models in this series