Tektronix Encore




Haefely PIM150
Oscillating Wave Surge Module, 100 kHz & 1 MHz

Compliance Testing - EMC, ESD, EMI, RFI >> EMC, EMI and RFI Test Systems and Analyzers >> Oscillating Wave Surge Module, 100 kHz & 1 MHz
Rent Used Test Equipment
Manufacturer: Haefely
Model: PIM150

Haefely PIM150 Oscillating Wave Surge Module, 100 kHz & 1 MHz

Electronic Test and Measurement Equipment

Haefely PIM150 Oscillating Wave Surge Module, 100 kHz & 1 MHz  Product Datasheet Download Product Datasheet

Rent Test Equipment

Product Overview

RENT Haefely PIM150 (call for availability)

The Haefely PIM150 with the PSURGE 8000 Surge Platform can perform all the programming functions required to perform IEC and ANSI testing without the need of a control computer. Voltage monitor circuits enable quick and easy verification of the impulse shape and amplitude. In addition, peak measurement circuits are used to help determine EUT PASS/FAIL criterion.

IEC 61000-4-12 and ANSI C37.90 describe an oscillating wave generator with defined open circuit waveforms parameters. The oscillating wave, also called a “damped sine” is used to test the immunity of electronic relays and relay systems mounted in an electrical substation or similar harsh environment. IEC product standards such as IEC 60255-22-1 include this wave shape too.

Safety is paramount when AC and impulse voltages are being used. The Haefely PIM150 High Voltage connections are all designed so no accidental contact can occur. In addition, the CDN input and output terminals use touch-proof connectors.

The Haefely PIM150 contains an integrated Coupling/Decoupling Network (CDN) for superimposition of the impulse on AC and DC power lines. The integrated CDN is specially designed to ensure wave shape integrity at the test system output. PIM 150 maintains wave shape AND amplitude, even with multiple coupling paths selected.

The integration in the WinFEAT&R control and reporting software package enhances an efficient set-up and operation of this test system. Most importantly, the test load can be transferred to a computer freeing valuable resources.

Features of the Haefely PIM150 Oscillating Wave Surge Module include:

  • 100kHz & 1MHz frequencies
  • 75ns rise-time
  • 3.3kV impulse voltage
  • Source Impedance 200 Ohm
  • Integrated three phase CDN
  • Variable burst duration

Highlights of the Haefely PIM 150 include:

  • International application – Specifically designed to meet and exceed the requirements of IEC, EN, and ANSI tests for power line applications.
  • Accurate Impulses - The PIM 150 wave shape and amplitude are guaranteed to conform to specification at the CDN output. Also with simultaneous, multiple coupling path selections.
  • Safe and Easy - The interlocked HV section and the specially designed output sockets, allow your operators to test safely and easily.
  • Sturdy and Reliable - Careful component selection ensures that the PIM 150 will continue to operate under the most strenuous testing regime.
  • Report Generation - The unit can automatically generate test reports without a computer. Add WinFEAT&R control and reporting software to collect and collate data in any format you like.

Applications for the Haefely PIM 150 Oscillating Wave Surge Module include:

  • Single & Three phase power line systems
  • IEC 61000-4-12 Power & Data lines
  • ANSI C37.90.1-2002 Power lines
  • IEC 60255-22-1 Measuring relays and protection equipment
  • IEEE 1613 Substation Equipment

Specifications of the Haefely PIM150 include:

  • Impulse Voltage 0.25 – 3.3kV
  • Burst Frequency 100kHz & 1MHz
  • Impulse Repetition 40 Hz & 400Hz
  • Source Impedance 200 ohms
  • Burst Duration 2 seconds to continuous
  • Damping Rate 50% Vpk between 5th and 10th peak
  • EUT Voltage 480Vac (phase - phase) / 110Vdc
  • EUT Current 16A ac/dc per path
  • Impulse Coupling Single & Multiple Path
  • Impulse Polarity Positive, Negative & Alternating
  • Impulse Output HV connector & CDN
  • EUT Safety switch 16A Thermo magnetic
  • Monitor Output BNC, volts (500 / 1)

Request A Quote

Rent      Buy      Repair
SUBMIT REQUEST
760-806-6600


Testimonial







Home   |   Rental Equipment   |   Equipment Sales   |   Repair & Calibration   |   Sell Your Equipment   |   About Us   |   Contact   |   Get A Quote   |   Blog    



YouTube Facebook Google Plus Paypal
Get the latest deals first. Subscribe to our newsletter.    SUBSCRIBE


© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML     
© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML

Axiom Test Equipment
2610 Commerce Way Vista, CA 92081
Phone: (760) 806-6600