Tektronix Encore




AE TECHRON 7548
Pulse Amplifier, High Power

Amplifiers - RF and Microwave >> Accessories and Other >> Pulse Amplifier, High Power
Rent Used Test Equipment
Manufacturer: AE TECHRON
Model: 7548

AE TECHRON 7548 Pulse Amplifier, High Power

Electronic Test and Measurement Equipment

AE TECHRON 7548 Pulse Amplifier, High Power Product Datasheet Download Product Datasheet

Rent Test Equipment

Available Option Configurations

Config-01

  • P - Precision Option
  • SIM-BNC-OPTOC - Amplifier In-series Connection Module
  • MSRP: $10,875 | In Stock!    GET QUOTE  

Product Overview

RENT AE TECHRON 7548 (Call for Availability)

The AE Techron 7548 amplifier is a DC-enabled, high-powered unit designed to provide very low noise and fast slew rates. It can operate in either voltage or current mode and can safely drive a wide range of resistive, inductive loads. The AE Techron 7548 amplifier is typically used as a power source for EMC testing in applications that require both continuous AC or DC signals and significant short term signals.

Features and Specifications of the AE Techron 7548 Amplifier include:

  • Features:
    • Over 12,000 watts peak for 40 mSec and 5,500 watts peak continuous into a 1-ohm load
    • 40 mSec pulses of up to 105 amperes peak into a 1-ohm load
    • System output of 800 volts and 70 amperes maximum are possible with multiple, inteconnected amplifiers
    • Frequency bandwidth:
      • DC to 50 kHz at rated power
      • DC to 100 kHz at reduced power
    • Rugged chassis:
      • For stand-alone or rack mounted operation
      • No additional power supplies are required
    • Protection circuitry protects AE Techron 7548 amplifier from:
      • Input overloads
      • Improper output connection (including shorted and improper loads)
      • Over-temperature
      • Over-current
      • Supply voltages that are too high or too low
    • Front Panel:
      • LED displays indicate Run, Ready, Standby, Stop and Fault conditions in the output stage
      • LSD Display:
        • Lists type of fault condition and gives suggested corrective action
        • Can be configured for up to 4 simultaneous displays reporting 1, 2 or all 4 of: Voltage Peak, Votage RMS, Current Peak, and Current RMS
      • Soft touch switches for Run (Enable), Stop, and Reset
    • Option "P" offers precision control of output offset, DC drift and gain linearity 
  • Specifications:
    • Frequency response:  DC - 30 kHz, +0.1, -0.5 dB
    • 8 ohm power response: 
      • DC - 40 kHz:  ± 180 Vpk
      • DC - 50 kHz:  ± 150 Vpk
      • DC - 150 kHz:  ± 50 Vpk
      • DC - 200 kHz:  ± 25 Vpk
    • Maximum continuous output power:  3300 watts RMS
    • Power sinking:  1.2 kVA at 120 VAC
    • Slew rate:  10 V/μSec
    • Phase response:  ± 5 degrees (10 hz - 10 kHz)
    • Unit to unit phase error:  +/- 0.1 degrees at 60Hz
    • Output offset:  
      • 7548:  < 5 mV, field adjustable to < 1 mV
      • 7548P:  < 200 µV
    • Output offset current:  < 10 milliamperes DC
    • DC drift:
      • 7548:  ± 1.5 mV
      • 7548P:
        • ± 400 μV (from cold to max operating temp)
        • ± 200 μV (after 20 minutes of operation)
    • Residual noise:
      • Unfiltered:  < 75 μV
      • Filtered (400 Hz 30 kHz):  < 55 μV
    • THD: DC - 30 kHz < 0.1%
    • Input Characteristics:
      • Balanced with ground:  3 terminal barrier block connector 20 k ohm differential
      • Unbalanced:  BNC connector, 10 k ohm single ended
      • Gain:
        • Voltage mode:  20 volts/volt
        • Current mode:  20 amperes/volt
      • Gain Linearity (over input signal, from 0.2V to 5V):
        • 7548:  0.1%
        • 7548P:
          • DC:  0.0125%
          • AC:  0.030%
      • Max Input voltage:  ± 10 V balanced or unbalanced
      • Input impedance:  20 kOhm differential
      • Input sensitivity:  3.0V input for 3800W output into 1 ohm (adjustable)
      • Common mode rejection range:  ± 11 VDC max
      • Common mode rejection ratio:  70 dB

Request A Quote

Rent      Buy      Repair
SUBMIT REQUEST
760-806-6600


Testimonial







Home   |   Rental Equipment   |   Equipment Sales   |   Repair & Calibration   |   Sell Your Equipment   |   About Us   |   Contact   |   Get A Quote   |   Blog    



YouTube Facebook Google Plus Paypal
Get the latest deals first. Subscribe to our newsletter.    SUBSCRIBE


© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML     
© 2020 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML

Axiom Test Equipment
2610 Commerce Way Vista, CA 92081
Phone: (760) 806-6600