Rent Amplifier Research 120T40G45 TWT Amplifier (Call for Availability):
The Amplifier Research 120T40G45 is a self contained, forced air cooled, broadband traveling wave tube (TWT) microwave amplifier designed for applications where wide instantaneous bandwidth, high gain and moderate power output are required. A reliable TWT subsystem provides a conservative 125 watts minimum at the amplifier output connector. Stated power specifications are at the fundamental frequency. The amplifier's front panel digital display shows forward and reflected output plus extensive system status information accessed through a series of menus via soft keys. Status indicators include power on, warm-up, standby, operate, faults, excess reflected power warning and remote. Standard features include a built-in IEEE-488 (GPIB) interface, 0dBm input, VSWR protection, gain control, forward and reflected RF output sample port, auto sleep, plus monitoring of TWT helix current, cathode voltage, collector voltage, heater current, heater voltage, baseplate temperature and cabinet temperature. Modular design of the power supply and RF components allow for easy access and repair. Use of a switching mode power supply results in significant weight reduction. The rated power is developed by efficiently power combining the outputs from two 80 watts (nominal) microwave tubes that are factory matched in gain and phase. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use but can be removed from the cabinet for rack mounting. The Amplifier Research 120T40G45 provides readily available RF power for a variety of applications in Test and Measurement, (including EMC RF susceptibility testing), Industrial and University Research and Development, and Service applications. This sub-octave amplifier features moderate harmonic content.
Functions and Specifications of the Amplifier Research 120T40G45 TWT Amplifier Includes:
POWER (fundamental), CW, @ OUTPUT CONNECTOR
Nominal: 140 watts
Minimum: 120 watts
Linear @ 1 dB Compression: 30 watts minimum
FLATNESS: ± 5 dB maximum
FREQUENCY RESPONSE: 40 - 45 GHz instantaneously
INPUT FOR RATED OUTPUT: 1.0 milliwatt maximum
GAIN (at maximum setting): 51 dB minimum
GAIN ADJUSTMENT (continuous range): 35 dB minimum
INPUT IMPEDANCE: 50 ohms, VSWR 2.0:1 maximum
OUTPUT IMPED: 50 ohms, VSWR 2.5:1 typical
MISMATCH TOLERANCE: Output isolator used to offer excellent
mismatch tolerance up to reflected power of 120 watts..
Will operate without damage or oscillation with any
magnitude and phase of source and load impedance. May
oscillate with unshielded open due to coupling to input.
Should not be tested with connector off.
MODULATION CAPABILITY: Will faithfully reproduce AM, FM, or
pulse modulation appearing on the input signal. AM peak
envelope power limited to specified power.
NOISE POWER DENSITY:
Minus 70 dBm/Hz (maximum)
Minus 75 dBm/Hz (typical)
HARMONIC DISTORTION: Minus 20 dBc typical
PRIMARY POWER: 190-260 VAC
50/60 Hz single phase 2 kVA maximum
RF input: Type 2.4 mm female on rear panel
RF output: Type WR-22 waveguide flange on rear panel
RF output sample ports: Type 2.4 mm female on rear panel
GPIB: IEEE-488 on rear panel
Interlock: DB-15 female on rear panel
COOLING: Forced air (self contained fans), air entry and exit in rear
WEIGHT (approximate): 105 kg, 230 lbs
SIZE (W x H x D): 50.3 x 43 x 76 cm, 19.8 x 17 x 30 in.
Request A Quote
Customers who viewed this also viewed
IFI Instruments T7525-500 TWT Amplifier, 2.5 - 7.5 GHz, 500W
Amplifier Research 200S1G6 Broadband Amplifier, 0.7 GHz - 6 GHz, 200W
Amplifier Research 200T1G3 Microwave Amplifier, 0.8 GHz - 2.8 GHz, 200W
Applied Systems Engineering 176X/KU Microwave TWT Pulsed Amplifier, 8 - 18 GHz, 1000W