Rent Amplifier Research 1000TP1G2Z5 Amplifier (Call for Availability):
The Amplifier Research 1000TP1G2z5 is a self contained, forced air cooled, broadband traveling wave tube (TWT) microwave amplifier designed for pulse applications at low duty factors where instantaneous bandwidth and high gain are required. A reliable TWT provides a conservative 1000 watts minimum peak RF pulse power at the amplifier output connector. Stated power specifications are at the fundamental frequency.
The amplifier's front panel digital display shows forward and reflected average power output or forward and reflected peak power, plus extensive system status information accessed through a series of menus via soft keys. Status indicators include power on, warm-up, standby, operate, faults, excess average or peak reflected power warning and remote. Standard features include a built-in IEEE-488 (GPIB) interface, 0dBm input, TTL Gating, VSWR protection, gain control, RF output sample ports, auto sleep, plus monitoring of TWT helix current, cathode voltage, collector voltage, heater current, heater voltage, baseplate temperature and cabinet temperature.
Modular design of the power supply and RF components allow for easy access and repair. Use of switching mode power supplies results in significant weight reduction.
Housed in a stylish contemporary cabinet, the amplifier provides readily available pulsed RF power for a variety of applications in Test and Measurement, (including EMC RF pulse susceptibility testing), Industrial and University Research and Development, and Service applications. AR also offers a broad range of amplifiers for CW (Continuous Wave) applications.
Functions and Specifications of the Amplifier Research 1000TP1G2Z5 Amplifier Include:
POWER (Fundamental), Peak Pulse, @ Output:
Minimum: 1,000 watts
FLATNESS: ±6 dB maximum
FREQUENCY RESPONSE: 1-2.5 GHz
INPUT FOR RATED OUTPUT: 1.0 milliwatt maximum
GAIN (at maximum setting): 60 dB minimum
GAIN ADJUSTMENT (continuous range): 35 dB minimum
INPUT IMPEDANCE: 50 ohms, VSWR 2.5:1 maximum
OUTPUT IMPEDANCE: 50 ohms, VSWR 2.5:1 typical
MISMATCH TOLERANCE: Output pulse width foldback protection at
peak reflected power exceeding 700 watts. Will operate without
damage or oscillation with any magnitude and phase of source
and load impedance. May oscillate with unshielded open due to
coupling to input. Should not be tested with connector off.
Pulse Width: 0.07 – 100 microseconds.
Pulse Rate (PRF): 100 kHz maximum
Duty Cycle: 4% maximum.
RF Rise and Fall: 30 ns max (10% to 90%).
Delay: 300 ns maximum from pulse input to RF 90%
Pulse Width Distortion: ±30 ns maximum (50% points
of output pulse width compared to 50% points of
input pulse width)
Pulse Off Isolation: 80 dB minimum, 90 dB typical
Pulse Input: TTL level, 50 ohm nominal termination
NOISE POWER DENSITY
(pulse on): Minus 70 dBm/Hz maximum;
Minus 80 dBm/Hz typical (pulse off):
Minus 140 dBm/Hz (typical)
HARMONIC DISTORTION: Minus 3 dBc maximum, minus 6 dBc typical
PRIMARY POWER: 190-260 VAC, 50/60 Hz single phase, 1.2 KVA maximum
RF input: Type N female on rear panel
RF output: Type DIN 7-16 female on rear panel
RF output forward and reflected sample ports: Type N female on rear panel
Pulse input: Type BNC female on rear panel
GPIB: IEEE-488 female on rear panel
Interlock: DB-15 female on rear panel
COOLING: Forced air (self contained fans), air entry and exit in rear.
SIZE (W x H x D): 50.3 x 26 x 94 cm, 19.8 x 10.3 x 37 in
WEIGHT (approximate): 57 kg, 125 lbs
Request A Quote
Customers who viewed this also viewed
Applied Systems Engineering 176X/KU Microwave TWT Pulsed Amplifier, 8 - 18 GHz, 1000W
Amplifier Research 200S1G6 Broadband Amplifier, 0.7 GHz - 6 GHz, 200W
Amplifier Research 200T1G3 Microwave Amplifier, 0.8 GHz - 2.8 GHz, 200W
Amplifier Research 250T8G18 Microwave Amplifier, 7.5 - 18 GHz, 250W