Rohde & Schwarz FSUP26 Signal Source Analyzer, 20 Hz - 26.5 GHz Rental, Repair, Rent, Used


Tektronix Encore




Rohde & Schwarz FSUP26
Signal Source Analyzer, 20 Hz - 26.5 GHz

Spectrum Analyzers and Signal Analyzers >> More than 8.5 GHz, up to 26.5 GHz >> Signal Source Analyzer, 20 Hz - 26.5 GHz
Rent Used Test Equipment
Manufacturer: Rohde & Schwarz
Model: FSUP26

CLICK TO ENLARGE Rohde & Schwarz FSUP26 Signal Source Analyzer, 20 Hz - 26.5 GHz

Electronic Test and Measurement Equipment

Rohde & Schwarz FSUP26 Signal Source Analyzer, 20 Hz - 26.5 GHz Product Datasheet Download Product Datasheet

Rent Test Equipment

Available Option Configurations

Config-03

  • B18 - Removable Hard Disk
  • B23 - 20 dB Preamplifier, 3.6 GHz to 26.5 GHz
  • B25 - Electronic attenuator 0 to 30 dB and Preamplifier, 10 MHz - 3.6 GHz
  • B4 - OCXO, low aging/improved phase noise at 10 Hz carrier offset
  • B60 - Low Phase Noise Board, necessary for Cross-correlation
  • K7 - FM Demodulator
  • MSRP: $131,500 | In Stock!    GET QUOTE  

Product Overview

The R&S FSUP26 Signal Source Analyzer combines the functionality of a high performance spectrum and signal analyzer with the advantages of a phase noise test system, all in a single box. The R&S FSUP26 is a unique and simple-to-use one-box solution for measuring oscillators and synthesizers in development and production applications. In addition, the Rohde & Schwarz FSUP26 leads to enormous cost reductions.

The Rohde and Schwarz FSUP26 analyzer is perfect for not only modern communications and broadcast systems, but also radar applications. Use the FSUP26 to measure phase noise and when characterizing oscillators, measure tuning slope, transient response, power, harmonics and spurious emissions, as well as amplifier noise. The integrated DC sources enable a wide range of additional measurements.

Features and specifications of the Rohde & Schwarz FSUP26 include:

  • Frequency range up to 26.5 GHz (up to 110 GHz with external mixers)
  • Low Noise DC outputs for supply and tuning voltages
  • Maximum flexibility for phase noise measurements
  • Oscillator characterization
  • Analysis of digital and analog modulated signals

Capabilities of the FSUP26 include:

  • Phase detector method with internal/external reference
  • Two-DUT method
  • High sensitivity
  • Automatic setting of all important parameters
  • Easy operation
  • Detection, suppression and listing of interference
  • Measurement of reference points as a function of frequency
  • Measurement of residual phase noise
  • AM noise

Abbreviated specifications of the FSUP26:

  • Operating Modes:
    • Signal Source Analyzer: 1 MHz - 26.5 GHz
    • Spectrum Analyzer: 20 Hz - 26.5 GHz
  • Signal Source Analyzer
    • Phase Noise Measurement:
      • w/ Spectrum Analyzer: 10 MHz - 26.5 GHz
      • w/ Phase Comparator: 1 MHz - 26.5 GHz
        • internal reference: 1 MHz - 26.5 GHz
        • external reference: 1 MHz - 8 GHz
      • w/ Phase Comparator & Cross-Correlation: 1 MHz - 26 GHz
  • Transient Measurement:
    • min. frequency offset: 10 MHz
    • max. frequency offset: 30 MHz
  • Residual Noise w/ Phase Comparator: 1 MHz - 8 GHz
  • AM Noise: 1 MHz - 8 GHz
  • Sensitivity with internal reference and internal phase detector:
    • Input level >+10 dBm, spurious and harmonics <–30 dBc, mode "averaged", +20 °C to +30 °C. LNA gain 40 dB, loop bandwidth =10 × frequency offset, max. 1 kHz. With the R&S Option B60 low phase noise Option B61 correlation extension option.
Freq Offset Input frequency, values in dBc (1Hz)                                                                        
  5 MHz 10 MHz 100 MHz 1 GHz 3 GHz 7 GHz 10 GHz 20 GHz
1 Hz  -114 -116 -87 -75 -62 -55 -52 -48
10 Hz -136 -135 -110 -91 -87 -80 -77 -71
100 Hz -143 -146 -134 -115 -106 -97 -95 -89
1 kHz -157 -161 -160 -134 -123 -118 -116 -112
10 kHz -165 -168 -168 -143 -131 -129 -126 -120
100 kHz -171 -170 -176 -158 -139 -140 -138 -132
1 MHz - -175 -177 -165 -160 -155 -150 -146
10 MHz - - -179 -172 -170 -170 -167 -161
30 MHz - - -179 -172 -170 -170 -170 -165

VCO Parameter Characterization:

Measurement Parameters              VCO tuning characteristic, VCO tuning slope, power, pushing ON/OFF, harmonics measurement, VCO DC characteristic, summary
Frequency Range   10 MHz - 26.5 GHz
Power Supplies tuning ports 2
  DC ports 2
  additional ports 1

 

 


Request A Quote

Rent      Buy      Repair
SUBMIT REQUEST
760-806-6600


Testimonial







Home   |   Rental Equipment   |   Equipment Sales   |   Repair   |   Sell Your Equipment   |   About Us   |   Contact   |   Get A Quote   |   Blog    


Facebook Google Plus Paypal
Get the latest deals first. Subscribe to our newsletter.    SUBSCRIBE


© 2017 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML     
© 2017 Axiom Test, All Rights Reserved
FAQ      Privacy      Terms      Site Map      Site Map XML

Axiom Test Equipment
2610 Commerce Way Vista, CA 92081
Phone: (760) 806-6600